Owens Corning Insulation Removal Nationwide

Owens Corning Insulation Removal in Los Angeles: What to Know First

Owens Corning insulation removal in Los Angeles typically costs between $1.50 and $3.25 per square foot, with most attic jobs completed in one day. We are an independent Owens Corning service provider, not a factory-authorized operation, which means we make removal decisions based on what is actually in your attic, not what protects a manufacturer warranty.

Call (254) 272-5876

This page is for Los Angeles homeowners who have Owens Corning fiberglass batts, blown-in loosefill, or foam board in their attic and need it removed. Wet insulation, rodent damage, or a remodel that opened old walls are the usual reasons. If you are looking at a mess of pink or yellow fiberglass and wondering what it takes to get it out and what goes back in, call (254) 272-5876 and we will walk you through it.

How Owens Corning Products Fail – and How We Fix Them

The majority of Owens Corning insulation failures in Los Angeles attics share the same root cause: moisture where it should not be, or age doing what age does. Here are the five patterns we see most often.

• Owens Corning Pink Fiberglas batts saturated from roof leaks. Once kraft-faced batts get wet, the paper facing promotes mold, and the fiberglass loses its ability to insulate. In Los Angeles, the leak is often concentrated around roof penetrations or valley flashing. Our fix: remove every affected batt, dry the cavity with air movers, and re-insulate only after the moisture source is stopped. Reinstalling over damp batts is how you get a repeat problem in six months.
• Owens Corning Atticat blown-in loosefill settled below its rated R-value. Atticat is a fiberglass loosefill that settles over time, especially in shallow attics where depth varies across the truss chords. We routinely measure attics in Van Nuys and North Hollywood that read R-19 or lower in spots, even though the Home Depot bag says R-30 at the labeled depth. Our fix: vacuum out the old Atticat, air seal the top plates, and blow fresh loosefill to a uniform depth with a written R-value on the proposal.
• Owens Corning FOAMULAR rigid board installed with the wrong facing orientation. FOAMULAR XPS panels installed backward or without a thermal break against sun-baked roof sheathing trap moisture at the seam lines. We see this in conditioned attics in the San Fernando Valley where the board faces the hot side. Our fix: remove the mis-installed panels, inspect the framing for moisture staining, and install new board with a proper gap and facing orientation matched to the local climate zone.
• Owens Corning EcoTouch batts shredded or displaced by rodents. Attics in older Los Angeles neighborhoods, especially near citrus trees, get rats and squirrels nesting in insulation. EcoTouch batts torn and scattered across the attic floor lose all air-sealing benefit. Our fix: full removal with HEPA-filtered vacuum, rodent-proofing consultation, and fresh batts cut tight around obstructions. No one should crawl through rodent-soiled insulation to run a cable or check a vent.
• Owens Corning Thermafiber mineral wool sagging after water exposure from HVAC overflow pans. Thermafiber is fire-resistant mineral wool, but it is not waterproof. When a condensate pan overflows in a Los Angeles attic AC system, the soaked Thermafiber compresses and pulls away from framing. Our fix: remove the affected sections, let the framing dry, repair the pan overflow, and reinstall. Reusing compressed wool is a false economy; the R-value is gone.

Our Owens Corning Insulation Removal Process

When you call Alden Attic Insulation for Owens Corning removal in Los Angeles, you get a written price before any equipment comes off the truck. That is how every job starts. Here is the sequence we follow.

1. 1
   Attic inspection and measurement. Our technician enters the attic, photographs the existing Owens Corning product and its condition, measures square footage and current depth, and checks for moisture, rodent activity, and air leaks.
2. 2
   Written proposal with one number. We give you a written price for removal, disposal, air sealing if needed, and new insulation. The number you approve is the number on the invoice. No door revisions.
3. 3
   Containment and removal. We set up a HEPA-filtered vacuum system rated for attic dust and remove the Owens Corning material, bagging it for disposal. The crew is uniformed and background-checked.
4. 4
   Air sealing and prep. After the old material is gone, we seal the top plates, around recessed lights, and around plumbing and electrical penetrations with a fire-rated sealant, then verify the vent baffles are clear.
5. 5
   New insulation installation. We install the replacement material to the R-value agreed in the proposal, whether that is blown-in fiberglass, batts, or another material. We install products from Owens Corning, Johns Manville, Knauf, Rockwool, CertainTeed, Icynene, Demilec, and GreenFiber so you can research the material before approving it.
6. 6
   Written 365-Day Done Right Promise. Every Alden job carries a written guarantee for a full year. If the work fails within 365 days, we return at no charge. That includes a free second visit if the repair fails within the guarantee window.

What Owens Corning Insulation Removal Costs in Los Angeles

Most Owens Corning insulation removal jobs in Los Angeles run between $1.50 and $3.25 per square foot, depending on attic access, material type, and how much disposal is required. A typical 1,200-square-foot attic in the Valley will land around $1,800 to $3,900 including new blown-in insulation to R-38. Contamination from rodents or moisture pushes the number higher because the disposal stream changes and the crew needs more protective gear and time.

What moves the price: attic height and access, whether the old material is batt or blown-in, how much has settled or become contaminated, and whether air sealing is included. We give the written price before work starts, not after we pull the old material and find a surprise. For an exact quote on Owens Corning insulation removal in Los Angeles, call (254) 272-5876 for a free estimate.

Why Los Angeles Homeowners Call Alden Attic Insulation for Owens Corning Work

Alden Attic Insulation is independently owned and operated, held to The Garrison Standard. That means the same written guarantee, the same background-checked and uniformed technicians, and the same live-answer phone policy for every job. Calls are answered by a real person 24/7, not a voicemail or a callback form. When you call at 11 p.m. with water stained through your ceiling, someone picks up.

We know Owens Corning products from the inside: the way Atticat settles, the way FOAMULAR panels behave in a hot Los Angeles attic, the way EcoTouch batts hold up after a roof leak. We also work with Reflectix and seven other brands, so if a different material is the smarter call for your attic, we will tell you that instead of pushing the familiar name. Bryce Holloway grew up in Reseda, where summer heat through a thin ceiling is something you feel before you understand it. Good insulation doesn’t announce itself – you just stop noticing the heat. We stand behind the work in writing for 365 days.

FAQs